User Tools
hardware:sw16
Differences
This shows you the differences between two versions of the page.
|
hardware:sw16 [2012/08/07 08:12] aaron created |
hardware:sw16 [2017/11/28 06:21] (current) jarrod |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| Using the inputs you can trigger rules, essentially using macros to control anything within the CFLink network.\\ | Using the inputs you can trigger rules, essentially using macros to control anything within the CFLink network.\\ | ||
| The SW16 is designed to be used with any keypad, custom or off the shelf. | The SW16 is designed to be used with any keypad, custom or off the shelf. | ||
| + | |||
| + | ===== Quick Reference Guide ===== | ||
| + | |||
| + | The SW16 Quick Reference Guide provides the basic information required to get started on a printable, black and white document that can be easily taken with you to a job site. [[http://www.commandfusion.com/sw16.html#downloads|Find the SW16 Quick Reference Guide here.]] | ||
| ===== Information Panel ===== | ===== Information Panel ===== | ||
| Line 36: | Line 40: | ||
| ==== 40 Pin Header ==== | ==== 40 Pin Header ==== | ||
| - | The 40 pin header on the front of the unit has pins allocated for all the dry contact inputs and LED outputs, as well as one pair for defining the LED voltage level.\\ | + | The 40 pin header on the front of the unit has pins allocated for all the dry contact inputs and LED outputs, as well as one pair for the LED supply voltage levels and one pair for ground.\\ |
| The SW16 ships with a ribbon cable ready for use. | The SW16 ships with a ribbon cable ready for use. | ||
| Line 56: | Line 60: | ||
| - Input 15 + | - Input 15 + | ||
| - Input 16 + | - Input 16 + | ||
| - | - Status LED 1 + | + | - Status LED 1 Cathode (-) |
| - | - Status LED 2 + | + | - Status LED 2 Cathode (-) |
| - | - Status LED 3 + | + | - Status LED 3 Cathode (-) |
| - | - Status LED 4 + | + | - Status LED 4 Cathode (-) |
| - | - Status LED 5 + | + | - Status LED 5 Cathode (-) |
| - | - Status LED 6 + | + | - Status LED 6 Cathode (-) |
| - | - Status LED 7 + | + | - Status LED 7 Cathode (-) |
| - | - Status LED 8 + | + | - Status LED 8 Cathode (-) |
| - | - Status LED 9 + | + | - Status LED 9 Cathode (-) |
| - | - Status LED 10 + | + | - Status LED 10 Cathode (-) |
| - | - Status LED 11 + | + | - Status LED 11 Cathode (-) |
| - | - Status LED 12 + | + | - Status LED 12 Cathode (-) |
| - | - Status LED 13 + | + | - Status LED 13 Cathode (-) |
| - | - Status LED 14 + | + | - Status LED 14 Cathode (-) |
| - | - Status LED 15 + | + | - Status LED 15 Cathode (-) |
| - | - Status LED 16 + | + | - Status LED 16 Cathode (-) |
| - | - Backlight LED 1 + | + | - Backlight LED 1 Cathode (-) |
| - | - Backlight LED 2 + | + | - Backlight LED 2 Cathode (-) |
| - | - Backlight LED 3 + | + | - Backlight LED 3 Cathode (-) |
| - | - Backlight LED 4 + | + | - Backlight LED 4 Cathode (-) |
| - | - Voltage Select 3.3V DC | + | - Voltage supply 3.3V DC max 500mA - To Anode (+) of LEDs |
| - | - Voltage Select 5V DC | + | - Voltage supply 5V DC max 1A - To Anode (+) of LEDs |
| - Ground | - Ground | ||
| - Ground | - Ground | ||
| - | **Note:** Short pin 37 or 38 to Ground to select the LED output voltage you wish to use. Only one of these should be shorted at any time. Leave the other floating. | + | **Note:** Share pin 37 or 38 (depending on what voltage your LEDs require) to the Anode (+ve, longest pin) of all LEDs. Cathode (-ve, short pin) for each LED should be connected to the appropriate LED pin on the SW16. |
| + | |||
| + | **Note:** If using RGB LEDs, make sure they are the 'common anode' type. Then pin 37 or 38 (depending on LED voltage) can be used for anode and each RGB cathode is connected to individual LED pins (17-36). | ||
| + | |||
| + | **Note:** If LEDs require voltage higher than 5V DC, an external power supply can be used up to 30V DC. Simply connect external power +ve to the Anode pins of the LEDs, and the external power supply -ve to pins 39 or 40 (ground) of SW16. Cathode of LEDs still connects to the appropriate LED pin on SW16 (pins 17 - 36). | ||
| {{ :hardware:sw16-voltage-selection.svg?nolink |}} | {{ :hardware:sw16-voltage-selection.svg?nolink |}} | ||
| Line 93: | Line 102: | ||
| - Data + | - Data + | ||
| - Data - | - Data - | ||
| - | - Power (12-24V DC) | + | - Power (9-30V DC) |
| - Ground | - Ground | ||
| Line 110: | Line 119: | ||
| {{ :hardware:sw16-ribbon-connected.png?nolink |}} | {{ :hardware:sw16-ribbon-connected.png?nolink |}} | ||
| {{ :hardware:sw16-with-ribbon-cable.png?nolink |}} | {{ :hardware:sw16-with-ribbon-cable.png?nolink |}} | ||
| + | |||
| + | ===== Factory Reset ===== | ||
| + | For information on how to rest your device to factory settings, see the [[hardware:device-resetting|Device Resetting Page]]. | ||
hardware/sw16.1344327167.txt.gz · Last modified: 2012/08/07 08:12 by aaron
